Please wait a minute...
工程设计学报
工程设计学报  2015, Vol. 22 Issue (6): 613-618    DOI: 10.3785/j.issn. 1006-754X.2015.06.016
通用零部件设计     
斜切进刀时采煤机滚筒力学特性分析
毛 君1，潘德文1，李 强2，谢 苗1，由旭平1
1. 辽宁工程技术大学 机械工程学院，辽宁 阜新 123000；
2. 宿州学院 机械与电子工程学院，安徽 宿州 234000
Analysis of mechanical properties of shearer drum in the process of oblique feed
MAO Jun1, PAN De-wen1, LI Qiang2, XIE Miao1, YOU Xu-ping1
1. College of Mechanical Engineering, Liaoning Technical University, Fuxin 123000, China;
2. College of Mechanical and Electronic Engineering, Suzhou University, Suzhou 234000, China
 全文: PDF(2024 KB)   HTML
摘要： 为了分析采煤机斜切进刀时滚筒力学特性，推导了采煤机在斜切进刀时单个截齿的截割阻力，应用叠加法得出了滚筒截齿总截割阻力，并运用挤压面积和煤岩破裂理论得出了滚筒轴向力.同时，以国产的MG400/940-WD交流电牵引采煤机为例，利用MATLAB对单个截齿的截割阻力、滚筒截齿总截割阻力及滚筒轴向力进行模拟.模拟结果表明：前滚筒最大轴向力约为最大总截割阻力的3.64倍，后滚筒最大轴向力约为最大总截割阻力的3.32倍.模拟结果对提高采煤机滚筒的稳定性及截齿的可靠性有一定的参考价值.
关键词： 采煤机滚筒;  斜切进刀;  截割阻力;  轴向力    
Abstract: In order to analyze the mechanical properties of shearer drum in the process of oblique feed, the single pick cutting resistance was calculated, the total cutting resistance was obtained by applying superposition method and the drum axial force was obtained by utilizing the extrusion area and theory of coal rupture. Meanwhile, taking domestic made MG400/940-WD AC electric haulage shearer as an example, MATLAB was used to simulate the single pick cutting resistance, the total cutting resistance and the roller axial force. The simulation results showed that the maximal axial force of front drum end plate was 3.64 times as much as the maximal total cutting resistance and the maximal axial force of hinder drum end plate was 3.32 times as much as the maximal total cutting resistance. The simulation results have certain value for improving the reliability of the tooth and the stability of the shearer.
Key words: shearer drum    oblique feed    cutting resistance    axial force
收稿日期: 2015-03-30 出版日期: 2015-12-28
基金资助:

国家能源研发（实验）中心重大项目（2010—2015）；辽宁省教育厅创新团队资助项目（LT2013009）；辽宁省煤矿液压技术与装备工程研究中心开放基金资助项目（CMHT-201206）
作者简介: 毛君（1960-），男，辽宁鞍山人，教授，博士生导师，从事机械设计及仿真、机电一体化研究，E-mail:13704181080@163.com.
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

毛 君，潘德文，李 强，谢 苗，由旭平. 斜切进刀时采煤机滚筒力学特性分析[J]. 工程设计学报, 2015, 22(6): 613-618.

MAO Jun, PAN De-wen, LI Qiang, XIE Miao, YOU Xu-ping. Analysis of mechanical properties of shearer drum in the process of oblique feed. Chinese Journal of Engineering Design, 2015, 22(6): 613-618.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn. 1006-754X.2015.06.016    或    https://www.zjujournals.com/gcsjxb/CN/Y2015/V22/I6/613

[1] 张强, 吴泽光, 周曰勇, 吴泽洋, 李立莹. 采煤机液压拉杠力学检测系统研究[J]. 工程设计学报, 2017, 24(5): 595-600.
[2] 杨超君, 章友京, 张涛, 陈志鹏, 孔令营. 调速型鼠笼式异步磁力联轴器的轴向力研究[J]. 工程设计学报, 2016, 23(3): 282-287.
[3] 周游, 李国顺, 唐进元. 截齿截割煤岩的LS_DYNA仿真模拟[J]. 工程设计学报, 2011, 18(2): 103-108.