Please wait a minute...
工程设计学报
工程设计学报  2015, Vol. 22 Issue (6): 562-568    DOI: 10.3785/j.issn. 1006-754X.2015.06.008
建模、分析、优化和决策     
薄壁管材滚珠旋压数值模拟研究
刘永锋1，高 新1，赵春江1，王 南2
1. 太原科技大学 重型机械教育部工程研究中心，山西 太原 030024；
2. 河北工程大学 机电工程学院，河北 邯郸 056038
Research on numerical simulation of ball spinning for thin-wall tube
LIU Yong-feng1, GAO Xin1, ZHAO Chun-jiang1, WANG Nan2
1. Heavy Mechanical Engineering Research Center of Ministry of Education, Taiyuan University of Science and Technology, Taiyuan 030024, China;
2. Mechanical and Electrical Engineering Institute, Hebei University of Engineering, Handan 056038, China
 全文: PDF(2490 KB)   HTML
摘要： 为了对滚珠旋压工艺进行研究，利用DEFORME-3D有限元软件建立了滚珠旋压无氧铜薄壁管材的三维模型并基于刚塑性有限元进行了仿真计算，分析了滚珠旋压加工中管材的金属流动规律、管材的应力分布及滚珠的旋压力，并将有限元模拟的滚珠旋压力与M.I.Rotarescu理论计算的旋压力进行了对比.结果表明，金属的塑性流动主要靠滚珠的挤压，滚珠与管坯接触区的摩擦力及芯模与管内壁的摩擦力均对旋压加工中的金属流动起阻碍作用.管材在旋压中处于三向压应力状态，其应力沿壁厚呈梯度分布.滚珠的径向力最大，其次是轴向力，切向力最小；随着旋薄量的增大,滚珠的三向旋压力均增大；管材壁厚的增大引起滚珠轴向、切向力的增大及径向力的减小.
关键词： 滚珠旋压;  薄壁管;  有限元模拟;  金属流动;  旋压力    
Abstract: In order to study ball spinning process, a 3D rigid-plastic finite element model of ball spinning made by oxygen free copper thin-wall tube was established under software DEFORME-3D. The forming process was simulated and calculated. The metal flow law of spinning process, the stress distribution of the thin-wall tube and the spinning force of the ball were analyzed, and the numerical value of spinning force of the ball calculated by finite element simulation was compared with that of M.I. Rotarescu‘ theory calculation. The results showed that metal plastic flow mainly depended on ball extrusion, the friction force between the ball and the contact zone of the tube billet and the friction force between the core-rod and the inner wall of the tube could inhibit the metal flow in the spinning process. The tube was under a three direction compressive stress and its stress was distributed on gradient along the wall thickness. The radial force of the ball was the biggest, the axial force was the second and the tangential force was the smallest. With the increase of the reduction of thickness, the spinning force of the ball increased. The increase of the wall thickness of the tube caused the increased of axial, tangential force and the decrease of radial force.
Key words: ball spinning    thin-wall tube    finite element stimulation    metal flow    spinning force
收稿日期: 2015-06-18 出版日期: 2015-12-28
基金资助:

国家自然科学基金资助项目（51375325）；河北钢铁联合研究基金资助项目（E2014402055）；山西省研究生创新项目（2015SY66）；太原科技大学研究生创新项目（20145028）
作者简介: 刘永锋（1988-），男，甘肃庆阳人，硕士生，从事材料塑性成形加工研究，E-mail:liuyongfeng1217@163.com. 通信联系人：赵春江（1975-），男，河北唐山人，副教授，博士，从事材料加工研究,E-mail:zhaochj75@163.com.
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

刘永锋，高 新，赵春江，王 南. 薄壁管材滚珠旋压数值模拟研究[J]. 工程设计学报, 2015, 22(6): 562-568.

LIU Yong-feng, GAO Xin, ZHAO Chun-jiang, WANG Nan. Research on numerical simulation of ball spinning for thin-wall tube. Chinese Journal of Engineering Design, 2015, 22(6): 562-568.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn. 1006-754X.2015.06.008    或    https://www.zjujournals.com/gcsjxb/CN/Y2015/V22/I6/562

[1] 李宗豪, 朱军, 陈伟球. 海上风电导管架陆地建造过程中的应力分析[J]. 工程设计学报, 2021, 28(2): 218-226.
[2] 赵晋芳, 谢里阳, 刘建中, 李 兵. 有限板共线多孔MSD疲劳裂纹扩展有限元模拟[J]. 工程设计学报, 2009, 16(4): 256-260.
[3] 孙爱芳，刘敏珊，董其伍. 特殊板壳式换热器封板的有限元模拟及强度研究[J]. 工程设计学报, 2008, 15(4): 295-299.