Please wait a minute...
工程设计学报
工程设计学报  2011, Vol. 18 Issue (2): 120-123    
工程设计理论、方法与技术     
铝合金轮毂弯曲疲劳试验的有限元模型
 陈继刚1, 张国智2, 林宇飞3
1. 燕山大学 机械工程学院,河北 秦皇岛 066004；2. 新乡学院 机电学院,河南 新乡 453000；
3. 燕山大学 艺术与设计学院,河北 秦皇岛 066004
Finite element model of bending fatigue test of aluminum-alloy wheel
 CHEN  Ji-Gang1, ZHANG  Guo-Zhi2, LIN  Yu-Fei3
1. School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, China;
2. School of Mechanical and Electrical Engineering, Xinxiang College, Xinxiang 453000, China;
3. School of Art and Design, Yanshan University, Qinhuangdao 066004, China
 全文: PDF(1243 KB)   HTML
摘要： 在铝合金轮毂产品开发阶段,针对试压铸小批量样件来进行的弯曲疲劳试验,是必须通过的台架试验之一．为避免试验的盲目性,减少试验次数,从而降低试验成本,提高试验的可靠性,有限元数值分析技术被采用,并已成为铝合金轮毂开发的先进设计技术手段．为正确应用该技术进行虚拟台架试验,必须建立有效的计算模型．基于理论分析与应用实践,考虑螺栓预紧力影响的非线性接触,以及加载杆与轮毂的材料异同,建立了轮毂弯曲疲劳台架试验的3种有限元力学模型：加载杆与轮毂为同种材料的整体线弹性分析模型、加载杆与轮毂为不同材料的线弹性分析模型、考虑各元件间的接触关系及螺栓预紧力影响的非线性分析模型．通过分析与比较,以及典型轮毂的试验验证,研究了以上3种有限元力学模型的优缺点、应用范围及计算的可靠程度,并以典型轮毂为例,用试验验证了模型的准确性．研究表明：加载非线性模型较为准确；线弹性模型可以用于轮辐处易发生疲劳破坏的分析；加载杆与轮毂材料异同对最大等效应力影响不大；对螺栓孔附近易破坏的轮毂,应采用考虑预紧力影响及非线性接触的模型．
关键词： 铝合金轮毂;  弯曲疲劳试验;  有限元模型;  螺栓预紧;  接触分析    
Abstract: In the development stage of aluminum-alloy wheel, the bending fatigue test is one of the bench tests that must be passed, to which the trial casting wheel on a small batch basis was put. To avoid experiments of blindness, reduce the number of tests, cut down the experiment cost and improve the reliability, the finite element method is applied, which is one of the advanced technologies in design stage. To apply the technology correctly, the effective calculation model must be built to simulate bench tests. Based on the theoretical analysis and practical case, considering the nonlinear contact relations from pretightening of blot and the material of difference between loading bar and wheel, three finite element models of bending fatigue tests were built, such as integral linear elastic model with loading bar and wheel in the same material, the separated linear elastic model with loading bar and wheel in different material, the nonlinear model considering with the affection of contact relations and pretightening force. According to analysis and confrontation, and verification test oriented with the typical wheel, theirs advantages and shortages, stress range and computing reliability were studied; the veracity of models was verified with the test of a typical wheel. The research shows the nonlinear load model is corrected, the linear elastic model can be used to analyze the fatigue of wheel which is easy to be broken near bolt hole, and the same\|different material of loading bar and wheel is less influential on the most equivalent stress, and the nonlinear contact model, considering with the affection of contact relations and pretightening force, was applicable to the analysis of the wheel which is easy to be broken near bolt hole．
Key words: aluminum-alloy wheel    bending fatigue test    finite element model    bolt pre-tightening load    contact analysis
出版日期: 2011-04-28
:  TH 123  
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
陈继刚
张国智
林宇飞

引用本文:

陈继刚, 张国智, 林宇飞. 铝合金轮毂弯曲疲劳试验的有限元模型[J]. 工程设计学报, 2011, 18(2): 120-123.

CHEN Ji-Gang, ZHANG Guo-Zhi, LIN Yu-Fei. Finite element model of bending fatigue test of aluminum-alloy wheel[J]. Chinese Journal of Engineering Design, 2011, 18(2): 120-123.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2011/V18/I2/120

[1] 黄龙艺, 王华, 嵇栩. 考虑紧固螺栓的三排滚柱式转盘轴承载荷分布计算[J]. 工程设计学报, 2021, 28(3): 350-357.
[2] 曾琪, 宾光富, 李超, 陈立锋. 联轴器扭转刚度对潜油电泵细长串联轴系扭振特性的影响研究[J]. 工程设计学报, 2021, 28(1): 89-94.
[3] 潘益明, 于兰峰, 韩露男, 单逸峰. 移动式架车机伸缩托头-托架接触的有限元分析[J]. 工程设计学报, 2019, 26(3): 315-320.
[4] 邓星, 于兰峰, 雷聪, 徐江平, 肖泽平. 无轨伸缩式门式起重机接触部位的有限元分析[J]. 工程设计学报, 2018, 25(1): 79-84,93.
[5] 梁云忠，乔玉鹏，金 波，伍 权，徐卫平. 毛刷电接触对的插拔力研究[J]. 工程设计学报, 2015, 22(3): 290-294.
[6] 郭佳民, 袁行飞, 董石麟, 赵晓旭. 基于实测数据的弦支穹顶计算模型修正[J]. 工程设计学报, 2009, 16(4): 297-302.
[7] 罗明军，王文林. 双扭杆双横臂独立悬架结构件有限元分析与关联式结构优化[J]. 工程设计学报, 2009, 16(2): 108-111.