Please wait a minute...
Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering)  2013, Vol. 14 Issue (8): 565-573    DOI: 10.1631/jzus.A1300114
Mechanical Engineering     
Fuzzy-based risk prioritization for a hydrogen refueling facility in Malaysia
Hue-yee Chong, Mahidzal Dahari, Hwa-jen Yap, Ying-tai Loong
Department of Mechanical Engineering, Faculty of Engineering, University Malaya, Kuala Lumpur 50603, Malaysia
Download:     PDF (0 KB)     
Export: BibTeX | EndNote (RIS)      

Abstract  Hydrogen is starting to be mentioned as an alternative fuel to replace the fossil fuel in future transportation applications due to its characteristics of zero greenhouse gas emission and high energy efficiency. Before hydrogen fuel and its facilities can be introduced to the public, relevant safety issues and its hazards must be assessed in order to avoid any chance of injury or loss. While a traditional risk assessment has difficulty in prioritizing the risk of failure modes, this paper proposes a new fuzzy-based risk evaluation technique which uses fuzzy value to prioritize the risk of various scenarios. In this study, the final risk of each failure modes was prioritized by using the MATLAB fuzzy logic tool box with a combination of two assessments. The first assessment was concerned with the criteria which affected the actual probability of occurrence. This assessment considered the availability of the standard that was applied to prevent the likelihood of the scenario occurring. On the other hand, the second assessment was focused on evaluating the consequence of the failure by taking into account the availability of detection and the complexity of the failure rather than only the severity of the scenarios. A total of 87 failure scenarios were identified using failure modes and effect analysis (FMEA) procedures on hydrogen refueling station models. Fuzzy-based assessments were performed through risk prioritizing various failure scenarios with a fuzzy value (0 to 1) and risk level (low, medium, and high) while a traditional risk assessment approach presented the risks only in forms of level (low, medium, and/or high). Availability of the fuzzy value enabled further prioritizing on the risk results that fell in the same level of risk. This study concluded that fuzzy-based risk evaluation is able to further prioritize the decisions when compared with a traditional risk assessment method.

Key wordsRisk criteria      Risk prioritization      Hydrogen refueling facility      Fuzzy logic     
Received: 08 April 2013      Published: 01 August 2013
CLC:  TK91  
  TP391  
Cite this article:

Hue-yee Chong, Mahidzal Dahari, Hwa-jen Yap, Ying-tai Loong. Fuzzy-based risk prioritization for a hydrogen refueling facility in Malaysia. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 2013, 14(8): 565-573.

URL:

http://www.zjujournals.com/xueshu/zjus-a/10.1631/jzus.A1300114     OR     http://www.zjujournals.com/xueshu/zjus-a/Y2013/V14/I8/565

[1] Jun-yi Liang, Jian-long Zhang, Xi Zhang, Shi-fei Yuan, Cheng-liang Yin. Energy management strategy for a parallel hybrid electric vehicle equipped with a battery/ultra-capacitor hybrid energy storage system[J]. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 2013, 14(8): 535-553.
[2] Ying-tai Loong, Mahidzal Dahari, Hwa-jen Yap, Hue-yee Chong. Development of a system configuration for a solar powered hydrogen facility using fuzzy logic control[J]. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 2013, 14(11): 822-834.
[3] José Luís Ponz-Tienda, Eugenio Pellicer, Víctor Yepes. Complete fuzzy scheduling and fuzzy earned value management in construction projects[J]. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 2012, 13(1): 56-68.
[4] Med Amine Laribi, Lotfi Romdhane, Sa?d Zeghloul. Analysis and optimal synthesis of single loop spatial mechanisms[J]. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 2011, 12(9): 665-679.
[5] Peng Zhao, Jian-zhong Fu, Hua-min Zhou, Shu-biao Cui. Automated process parameters tuning for an injection moulding machine with soft computing[J]. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 2011, 12(3): 201-206.
[6] Yong ZHANG, Shen-sheng ZHANG, Song-qiao HAN. Adaptive service configuration approach for quality of service management in ubiquitous computing environments[J]. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 2009, 10(7): 964-975.